The water fuel car is a boon for people who want to save themselves the expenditure that arises out of booming fuels. Also the water fuel car is the best eco friendly solution that you can think of because the fuel is used efficiently rather than being used to emit poisonous gases that harm the environment.
The water fuel car technology is based on the premise of running the car partly on gas and partly on water. The electricity from the vehicle’s battery is used to break down water and produce a gas called hydroxyl gas or Brown gas. The hydroxyl gas is known to be ten times more efficient than the standard gasoline. Noticeably a large amount of gasoline (up to 75 percent) in car is totally wasted, which is why it makes more sense to switch to Brown’s gas.
The water fuel kit consists of things that can be purchased from a nearby hardware store and electrical store: sealed quartz side container, electrolyzer, electric component unit, electrical wiring, CPVC pipes, baking soda and an automotive fuse. The cost of all these materials comes to less than cheap $100. Hydrogen gas is created by moving the electrical charge through the water, powered by the car battery. The H2O (water) is converted to HHO (Brown’s gas) and the hydroxyl gas is then passed directly to the engine where it is mixes with the air mixture to burn gas efficiently. The function of the bubbler is to prevent any water vapor from getting into the engine.
Drivers who have opted for water fuel car have tremendously benefited by this move, considering the amount they stand to save on fuel costs. Also the engine of your car has more chances of lasting for a considerably longer period of time. The water fuel car is run by a water fuel kit which works as a fuel supplement to the usual gasoline. More than 10000 cars and trucks in US have already incorporated the water fuel technology. People who drive water fuel cars have stated that the mileage of their vehicles have zoomed from a mere 35 percent to 75 percent. One can imagine the amount of savings on fuel costs. Considering the fact that fuel and oil costs have gone through the roof, due to inflation, the savings hold a lot of value in today’s times. If you sit down and compare the benefits of your usual gasoline powered car and the water fuel car, you will find that the latter outweighs the benefits of the former in every plausible manner.
Most people do not think of contaminants getting into their water supply via their irrigation system, but this can actually occur and it can be dangerous. Contaminants can transfer or backflow from your irrigation line into the water supply in your home. The valve that turns your water on and off may not be enough to keep the backflow from occurring, which is why it is recommended that you install a backflow preventer on any irrigation system that you install residentially or commercially. There are different types of backflow preventers, so it is important that you choose the right one for your needs. What are the different types of backflow preventers that you can use for your home or business?
-Reduced pressure type backflow preventer. This backflow preventer is normally used in industrial uses, because it is made for high hazard usage. It can be quite expensive as well, which is why it is much more commonly used in commercial settings. It needs to be installed 12 inches above the ground, so that it can work most efficiently. Outside installation is most commonly recommended, because they can spit out water if they detect backflow or if they break down. If you install this backflow preventer indoors, you will want to make sure that there is a drain that will remove the water from inside your home or business.
-Double check backflow preventer. This is a double-valved system that has a shut-off valve on each end to prevent backflow. The two seals in the system work together to prevent contaminated water from flowing back into the water system of your home. It is important to check with your local officials if you are considering this type of backflow preventer, because they are considered illegal for use in some areas of the country.
-Atmospheric vacuum breaker. This is the most expensive of the backflow preventers. The AVB is installed on the line right after the control valve and if your irrigation system has more than one control valve, an AVB must be installed after every control valve to do its job properly. It needs to be installed 6-inches above the highest sprinkler head, drip emitter outlet, or bubbler. Check with your local officials if you are considering an atmospheric vacuum breaker. Some municipalities do not allow their use.
-Anti-siphon valve. The anti-siphon valve is an automatic or manual control valve that has a built-in atmospheric vacuum beaker. This is the most common backflow preventer that is used in residential applications, because they are not that expensive and they are simple to use and install. However, some cities do not allow this type of backflow preventer, so check with your local officials to make sure that it is legal to use it on your home.